Check Also
Automatic Tool Change
  1. Home
  2. Blog

Rinnai Code 11

Rinnai Code 11

Table of Contents

Rinnai Code 11 Rinnai Error Code 11 This error code indicates that the temperature sensor is disconnected or short-circuited. Common causes are a faulty sensor or an incorrectly installed sensor. The sensor must be replaced to solve this problem

Please see the following link for more information:

https://www.rinnai.us/rinnai-tankless-water-heaters/error-codes

I have a Rinnai tankless heater that has been working without problems. From time to time we get error code 11, which is the exhaust sensor is too hot. I have checked the wiring and tightened the connections. This problem usually clears itself and goes away for several weeks or more. I have more recently started getting error code 11, but does not clear on its own. I have to turn off power to the unit and then it resets itself and works fine again for a while. Any ideas?

The water temperature has been set too high.

Turn the temperature down to at least 120°F (49°C).

The hot water supply piping is clogged or blocked.

Turn off the unit and call a licensed Rinnai installer.

11 Flashing

Overheat warning.

The heat exchanger is likely over-heating. Check for blockages in the air inlet and make sure there is a free flow of air in the room.

Check for incorrect exhaust placement or diameter.

what do you do when you get a Rinnai tankless water heater error code 11? You get a code 11 on your Rinnai tankless water heater when the gas pressure is too low or the gas type is incorrect. This can be caused by a faulty regulator, improper gas setting on the unit, or high demand.

The Rinnai Tankless Water Heater is designed to provide an endless supply of hot water. However, like any appliance, it may experience problems. When the Rinnai Tankless Water Heater malfunctions, it displays error codes that tell you exactly what is wrong with it so that you can troubleshoot and fix the problem easily

if the Ignition Lockout Mode is active wait at least 5 minutes to pass before turning the gas valve ON.

11 High temperature limit switch has opened. Reset by turning the power off at main switchboard and wait three minutes then turn the power back on again. If the fault reoccurs then there is a fault with the gas supply or flueing, contact your plumber.

Please contact our Technical Support Department at 1-800-621-9419, option 3.

rinnai water heater code 11 p1 means the burner is getting a flame signal but not sensing a flame. Check the wire connections to the flame rod. If this does not work, replace the flame rod.

Rinnai is a leading supplier of water heaters for commercial and residential use. These units are designed to last for years, but you may sometimes experience problems with the electronics on these devices. One issue that may occur is the Rinnai error code 11, which generally means there’s an issue with the flame rod or the igniter.

The Rinnai natural gas water heater uses a gas burner to heat up the water in the tank. In order to get the flame started, the unit uses an igniter to light up fuel. Once it’s lit, the flame rod will keep it burning until the temperature gets high enough to turn off. This process repeats itself until you turn off your hot water.

Error Code 11

If you get a Rinnai error code 11, it usually means there’s an issue with either the flame rod or igniter that could be preventing your water heater from starting properly.

How to Fix It

Before you do anything else, try resetting your unit by flipping the circuit breaker it’s connected to for about 15 seconds. Then turn it back on and wait for about two minutes for your unit to restart. If this doesn’t fix your problem, try turning off your

Rinnai tankless water heaters use a condensing technology that provides the highest energy efficiency in the industry. The Rinnai tankless water heater contains an electronic control board that monitors and manages the internal functions of the unit through a series of sensors.

One of these sensors is called the air-fuel ratio sensor, which monitors the amount of oxygen in the exhaust gases of your water heater. If there is a fault in the air-fuel ratio sensor, it will send an error code to the control board to indicate that there is a problem with the sensor.

The air-fuel ratio sensor error code will appear when you press on any buttons on your Rinnai tankless water heater. The error code will be displayed as “11” on your digital display screen. This means that there is a problem with your air-fuel ratio sensor and you need to replace it

Good afternoon,

I am sending you this message to enquire about the progress of your investigation on the Rinnai heater. I recently purchased a new Rinnai Heater and was wondering if it is safe to use? I have heard some rumours that the product has been recalled due to safety issues.

Your help would be much appreciated.

Kind Regards,

The gas supply is insufficient. The gas valve is closed, or the gas supply is shut off.

The inlet filter is clogged. Remove any foreign matter from the inlet filter.

The water pressure is low. The water pressure is below 1.0 kPa (0.1 kgf/cm2).

The water flow rate is low. The water flow rate is below 0.01 MPa·s (0.01 l/min).

  1. Flammable gas leak detection

(A) Definition

“Flammable gas leak detection” means a device or system of devices used to detect the presence of flammable gases in areas where such gases may be present in quantities that could create explosive or ignitable mixtures. The device shall be designed and calibrated to respond to the flammable gases for which protection is intended, and to operate within a range of concentrations from 20 percent of the lower explosive limit (LEL) to 100 percent of the LEL. The system shall include manual shutoff valves located at or near the source of supply, and the design shall provide for automatic shutdown of the source upon detection of gas and ignition.

(B) Installation requirements

(1) Location. The sensor shall be located at ground level or lower in accordance with NFPA 54, NFPA 58, or NFPA 59A, as applicable.

(2) Detection limits. Flammable gas leak detectors shall be capable of detecting methane at 100 percent of the LEL throughout all occupied spaces on every floor level and in every room containing an appliance with direct venting through a sidewall or roof.

(3) Operation verification method. Flammable gas detectors shall contain an operating verification feature

Bültenimize Katılın

Hemen ücretsiz üye olun ve yeni güncellemelerden haberdar olan ilk kişi olun.

About Author